Origin-live All non dual pivot arms Bedienungsanleitung PDF herunterladen

Page1

Introduction

Give

special attention to underlined text in these instructions.

Give special attention to underlined text in these instructions.Give

Please note that on some arms, it may seem that there is “play”

in the bearings - this is deliberate and bearing tension should

not be altered or degradation will result - The bearing races are

high quality and devoid of play, however the bearing housings

are carefully dimensioned to allow a loose ﬁ t, thus “ﬂ oating” the

arm rather than rigidly coupling it to the deck.

Mounting the arm

Arm mounting methods are critical for best performance

and vary depending on the arm AND the make of your

turntable

. This section caters for various scenarios. If possible,

refer also to the mounting instructions from your turntable

manufacturer.

Mounting hole dimensions

Most decks come with a predetermined hole position

speciﬁ caly set up for arms with “ Rega “ geometry but if this is

not the case with your deck then use the following - Mounting

dimensions for Origin Live & modiﬁ ed Rega arms require

centre of platter, to centre of arm hole, to be approx 223mm

plus or minus 2mm tolerance. The hole diameter for the arm

is 23mm to 25 mm (24 - 25mm if a threaded vta adjuster is to

ﬁ t). If you need to modify your existing armboard to enable an

arm to ﬁ t, please refer to our web site FAQ (frequently asked

questions) in the tonearm section.

For the newer 3 point mounting

- once the large centre hole

For the newer 3 point mounting - once the large centre hole For the newer 3 point mounting

(24mm diameter approx) is drilled, insert and position the

arm. With the arm at right angles to the front of the deck,

mark the 3 mounting holes using the arm base as a jig. A 3mm

drill rotated by your ﬁ ngers will do the trick - idealy you can

mark and drill just one hole, then ﬁ t a bolt or screw into it, and

then mark / drill the other 2 holes.

Mounting

washers and vta adjusters

To allow vta adjustment and improve performance,

various

washers a

re used

First of all, threaded vta adjusters can be ﬁ tted to all Origin

Live arms except the 3 point mounting arms (All OL1

versions).

Next there is a choice of mounting cork washers, or no washers

- please refer to the table below as a quick reference as to which

to use. The ﬁ tting and other details are explained more fully in

the following sub-headings.

OL1 to Silver

& all Rega arms

Origin Live Encoun-

ter and above

Metal & non wood

based armboards

Cork Washers & spac-

ing wahsers if needed

Cork Washers

Wood based

armboards

Only spacing washers

if needed

No washers

Installing

ORIGIN LIVE & REGA ARMS

PLEASE NOTE: The sound of new arms

and rewires will improve signiﬁ cantly over the

ﬁ rst 2 weeks as items bed down and arm wires

burn in.

1 2 3 4 5 6

Inhaltsverzeichnis

Seite 1 - ORIGIN LIVE & REGA ARMS

Page1IntroductionGive special attention to underlined text in these instructions. special attention to underlined text in these instructions.Give spec

Seite 2 - Connecting the arm

Page2MO U N TING T H E ARM ON M K 2 ORIG I N LI V E DECKS ON LYArms with a threaded base ﬁ t Origin Live decks as per the t Origin Live decks a

Seite 3 - Cartridge set up

Page3CO N N ECT TH E A RM TO YOUR PHO N O STAGE / A MPLIFI E RNormaly this is straightforward, however if you have if you have bullet plug

Seite 4 - ******EXTREMELY IMPORTANT

Page4VTA A DJUSTM E N TTo allow the cartridge needle to track at the correct VTA (vertical tracking angle) it is important that the base of the ar

Seite 5 - Hi-Fi cartidges explained

Page5all three, to experimentally move from one type of adjustments to the next, then to the next, in order to balance the optimization for all three.

Seite 6 - Proper care and maintenance

Page6Alignment for hi-ﬁ cartridges needs to be optimised in three different planes. However, it cannot be perfect in all three planes, so it

Kommentare zu diesen Handbüchern

Keine Kommentare

Origin-live All non dual pivot arms Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Hardware Origin-live All non dual pivot arms herunter. Origin Live All non dual pivot arms User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Hardware Origin-live All non dual pivot arms